Hello Guest!

Annoying Squeak

  • 6 Replies
  • 451 Views
*

Taildragger

  • ****
  • 88
    • View Profile
  • OwnPC: Yes
  • NewUsed: Used
  • PurchDate: 02/20
  • Model: 2100
  • ModelYear: 2007
  • Slide: Yes
  • IntColor: Cherry/Desert Sand
  • ExtColor: Grey
  • Location: Alaska
Annoying Squeak
« on: May 06, 2022, 11:22:58 pm »
Unlike a vehicle, squealing politicians are usually trying to divert your attention from the real problem.  Instead of having the listener focus on real issues to reveal how unseemly their behavior might be.  Whereas, with a machine, an annoying squeak usually leads to a problem that can't be ignored.

I found the length of black iron pipe connecting the LP gas tank to the utility cabinet is essentially free floating.  Suspended by the rubber hose exiting the tank and unfettered before entering the utility connection.  Every bump in the road causes the weight of the unsupported pipe to bounce and "squeak".

Not particularly noticeable at highway speed, it is impossible to ignore at city speeds.  Especially, at intersections or other grade variations. 

Pinpointing the problem is easy.  Just crawl under the rig and confirm it. Effortlessly moving the pipe up and down to replicate travel over a bump generates a squeak that is unmistakable.  And, for me, ignoring it eventually becomes impossible.

I put a u-bolt over the black iron pipe and an eyebolt into an existing hole in the adjacent truck frame.  I connected the two to form a pipe brace midway along the route.  Effectively suspending the pipe with a sling and restricting movement. 

I am currently on the road and made the repair in a hardware store parking lot.  About four thousand miles from home, I am grateful to be rid of the annoyance.  I am also curious why the restraint wasn't installed by the factory. 

*

fandj

  • ******
  • 336
    • View Profile
  • OwnPC: Yes
  • NewUsed: New
  • Model: 2552
  • ModelYear: 2016
  • Slide: Yes
  • IntColor: Graystone
  • ExtColor: Nightscape - full body
  • Location: Virginia
Re: Annoying Squeak
« Reply #1 on: May 07, 2022, 04:26:34 am »
Good analogy and thanks for the tip.

*

donc13

  • *******
  • 1200
    • View Profile
  • OwnPC: Yes
  • NewUsed: New
  • PurchDate: 03/2015
  • Model: 2551
  • ModelYear: 2015
  • Slide: Yes
  • IntColor: Nightscape/Hickory
  • ExtColor: White/Nightscape
  • Location: Colorado
Re: Annoying Squeak
« Reply #2 on: May 07, 2022, 06:57:01 am »
Taildragger,

I am guessing it's something that was overlooked.   On my 2015 model, I have no looseness.
---
Don and Patti

*

Ron Dittmer

  • *******
  • 5407
  • Ron and Irene
    • View Profile
    • My 2007 2350 Phoenix Cruiser
  • OwnPC: Yes
  • NewUsed: New
  • PurchDate: June 2007
  • Model: 2350 Ford
  • ModelYear: 2007
  • Slide: No
  • IntColor: Cherry Green&Gray
  • ExtColor: Full Body Gray
  • Location: N/E Illinois
Re: Annoying Squeak
« Reply #3 on: May 07, 2022, 08:31:54 am »
Same topic, different source.

Many years ago, we had an irritating squeak in the B+ area above the driver.  As the driver, if I opened the left-side glass-panel cabinet door and put my hand on the ledge, and applied some body weight while driving, the squeak went away.

Back home, I called Kermit (the previous owner and founder of Phoenix USA) who had me DO THIS.  I addressed the problem back in 2013 and the irritating squeak has not yet returned today in 2022.

A few years ago, I softened the front suspension DOING THIS which of coarse would help to reduce any such issues, developing or reoccurring.
« Last Edit: May 07, 2022, 08:45:24 am by Ron Dittmer »
Ron (& Irene) Dittmer

*

mikeponiatowski

  • ***
  • 22
    • View Profile
  • OwnPC: Yes
  • NewUsed: Used
  • Model: 2100
  • ModelYear: 2007
  • Slide: Yes
  • IntColor: Cherry/Brown/Beige
  • ExtColor: White/Green
  • Location: White Lake, Michigan
Re: Annoying Squeak
« Reply #4 on: May 22, 2022, 01:08:44 pm »
I also have an '07 2100.  I appreciated the "heads up" on the propane tank pipe situation.  I just checked mine and it seems to be secure.  I may still add a hanger of some type to reinforce it.  While under the rig and looking up at the lp tank, I see quite a bit of paint peeling off the lp tank and some rust starting to form.  Can the lp tank be re-primed/painted?

*

Ron Dittmer

  • *******
  • 5407
  • Ron and Irene
    • View Profile
    • My 2007 2350 Phoenix Cruiser
  • OwnPC: Yes
  • NewUsed: New
  • PurchDate: June 2007
  • Model: 2350 Ford
  • ModelYear: 2007
  • Slide: No
  • IntColor: Cherry Green&Gray
  • ExtColor: Full Body Gray
  • Location: N/E Illinois
Re: Annoying Squeak
« Reply #5 on: May 22, 2022, 08:07:10 pm »
Can the lp tank be re-primed/painted?
Absolutely!!!  You won't break any LP tank rules.  Actually it is quite the opposite.  Officially, filling a rusted tank breaks the rules.

This is why you see those BBQ grille tanks in the "exchange" cage repainted often.
« Last Edit: May 22, 2022, 08:11:05 pm by Ron Dittmer »
Ron (& Irene) Dittmer

*

mikeponiatowski

  • ***
  • 22
    • View Profile
  • OwnPC: Yes
  • NewUsed: Used
  • Model: 2100
  • ModelYear: 2007
  • Slide: Yes
  • IntColor: Cherry/Brown/Beige
  • ExtColor: White/Green
  • Location: White Lake, Michigan
Re: Annoying Squeak
« Reply #6 on: May 23, 2022, 05:27:25 am »
Awesome!  Thanks.